|
We're currently out of stock on the 5/8" compression fitting that you'll find in the options dropdown for the weldless versions. End of February ETA. We have plenty of the plain valves and regular weldless bulkheads.
|
|
Model: 12Diptube - $19
This series of diptubes is based on 1/2" OD thickwalled 304 Stainless Steel tubing bent with a mandrel bender and comes with a stainless compression fitting with 1/2" Male OD threads. This is the only option we offer for vessels with 1/2" couplings welded in and is a reasonable option for those not concerned with maximum flow rates that are acheived with the larger 5/8" OD diptubes. The height of these assemblies is approximately 3" from fitting center to bottom of the diptube which is just about right for converted kegs. The depth can be trimmed with a hacksaw if necessary.
|
|
Model: 3PBV - $18.99
This is stainless 3-piece body (meaning that it will easily disassemble while still installed for cleaning every few months) with a non-restricing "full port" ball and 1/2" NPT female threads on both ends. Use them on your boil kettle, HLT, mash tun, pumps, etc. As shown in the pic, they have a locking mechanism on the handle. It can be pried off if you don't want the lock.
|
|
Model: WL2PBV - $24.99 (varies with options)
You've been asking for weldless valves for a long time to make this more of a one stop shop. Here they are. This kit uses all stainless and silicone parts for long life and heat tolerance. Drill a hole in your pot, install the kit, and stop trying to lift all that weight to pour into the fermenter.
This kit will work in metal vessels as well as cylindrical coolers that have thin walls at the drain location such as the Igloo 10 Gallon beverage dispenser. Maximum wall thickness is 3/16".
|
|
Model: Bulkhead - $11.99 +
  If you've asked us about a weldless bulkhead and here it is. This iweldless bulkhead is meant for a thin wall vessel such as a keg or pot. It will also work in cylindrical beverage coolers such as the Igloo 10 gallon or any other cooler where the wall thickness is less than 3/16".
It includes all stainless 1/2" NPT parts including locknut, threaded close nipple, silicone washer (with spare), metal shim washer and one variety of interior connection fitting (see options). This kit requires the addition of a ball valve to complete the kit. Order this if you already have a ball valve otherwise you can get the bulkhead as part of a kit in the ball valve section here.
|
|
|
Model: Diptube - $9 +
This variety of diptubes offered here will complete the install of any drain bulkead for any vessel. These are most important in converted keg based vessels to remove the last 2 gallons or so that sit below the drain port. In a hot liquor tank, you want to be able to drain it nearly completely. If you use hop socks in your boil kettle, you can also use a diptube all the way to the bottom of the kettle. These come in copper or stainless.
|
|
Model: 2PBV - $13.99
You've been asking for valves for a long time to make this more of a one stop shop.This is stainless 2-piece body with a non-restricing "full port" ball and 1/2" NPT female threads on both ends. Use them on your boil kettle, HLT, mash tun, pumps, etc.
|
|
Model: WL3PBV - $30.99
You've been asking for weldless valves for a long time to make this more of a one stop shop. Here they are. This kit uses all stainless and silicone parts for long life and heat tolerance. Drill a hole in your pot, install the kit, and stop trying to lift all that weight to pour into the fermenter. This kit uses a premium 3-piece valve that can be taken apart while one half of the body remains installed.
This kit will work in metal vessels as well as cylindrical coolers that have thin walls at the drain location such as the Igloo 10 Gallon beverage dispenser. Maximum wall thickness is 3/16".
|
|
|
|
|
|
