Home > Equipment > Fittings / Camlocks / Triclover > Triclover >

TRUE Weldless 1.5" TC Triclamp Bulkhead - STD up to 1/8" Wall
TRUE Weldless 1.5" TC Triclamp Bulkhead - STD up to 1/8" Wall


 
Alternative Views:


Our Price: $24.00

Quantity in Stock:39


Product Code: TC15WLF
Qty:

Description
 
The 1-1/2" Triclover (TC) weldless bulkhead flange allows you to add a TC port to any tank or kettle with absolutely no welding or soldering. Just drill a hole and tighten the locknut. Done!
The flange measures 2" like all other 1.5" TC ferrules, and the overall length is just under 1". The ID is 1-3/8 just like standard 1.5" weld ferrules. The short length of this ferrule makes it possible to use ripple style heating elements and not have the foldback make contact with the ferrule. These are extremely high quality pieces machined out of 304SS and polished to perfection (except for the locknut which is cast finish 304SS. Let's repeat this since we get the question constantly. YES! Ripple style elements fit into these with NO PROBLEM at all when using the ETC3 Hot Pods as the element housing/adapter.

The silicone O-ring is included and gets captured in a groove like our other True Bulkheads.

This is the STD length version which has enough thread length for wall thickness of up to 1/8" (or 3/16" as long as the install surface is completely flat like a lid). We also have an XL version that can accommodate wall thickness of up to 1/2".

Installation Notes:
  • Hole Size Required - 1-5/8" or 41mm. Note that the most pleasant tool to use for this is a knockout punch set. Since they are extremely cost prohibitive, the next best option is our tungsten carbide hose saw (40mm). After deburring the 40mm hole, the result is a clean 41mm hole. See the accessories column on the right for the bit.
  • The oring contact is on the flange side of the fitting so make sure there are no burrs on that side of the hole.
  • The lock nut hex measures 2-1/16" or 52mm. Turning it with an adjustable wrench does NOT work well. You'll need a socket or a box wrench. Since these tools are very rare, we offer a socket as an accessory. It requires a 1/2" drive ratchet.
  • The front of the flange does not have flats for a wrench. The easiest way to hold the front of the flange for tightening is to clamp any other TC part on with the gasket and clamp (a blank cap works great). Once tight, you can insert a long rod or screw driver into the hole of the wingnut.

We've tested this on a pot measuring as small as 12" in diameter. Anything smaller may work but we don't know for sure. Larger diameters or flat areas are no issue at all.


Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 45 Click Here to Write a Review »

Accessories
Tungsten Carbide Hole Saw, 40mm or 1-5/8 Drill Bit, for Stainless Steel
Our Price: $19.00

Add
Tungsten Carbide Hole Saw, 40mm or 1-5/8 Drill Bit, for Stainless Steel
52mm Socket Tool for Weldless 1.5" TC Bulkhead
Our Price: $15.00

Add
52mm Socket Tool for Weldless 1.5" TC Bulkhead
1.5 TC Silicone Gasket (Heat Resistant to 400F)
Our Price: $2.00

Add
1.5 TC Silicone Gasket (Heat Resistant to 400F)
1.5 TC Clamp
Our Price: $7.00

Add
1.5 TC Clamp


  0 of 0 people found the following review helpful:
 
5 of 5 Works on pot diameter 11.80" March 1, 2024
Reviewer: Jeff from Windsor, CO United States  
Tested this bulkhead on a boiler with diameter of 11.80" and it kept its seal. Good Stuff

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Nice product September 26, 2023
Reviewer: Ed Carlson from Monument, CO United States  
Great way to add ports to my brew kettle; seals well if you follow the video instructions! I advise you get the drill bit (and socket) to go with this as it would have a chore to make a clean, proper sized hole without it. I used a hammer drill, which has a second handle so I had no problems with the bit jamming as it cut through.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 June 8, 2023
Reviewer: Kevin Johnson from Spalding, SK Canada  
quick service and shipping into Canada, no issues.
All is good, thank you.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Bulkhead fittings are great May 31, 2023
Reviewer: Bryan Miller from Pittsburgh, PA United States  
Installed in the holes that were make with the recommended tungsten carbide hole saw.  The fittings are well made and installed as expected.  No leaks.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 September 17, 2022
Reviewer: Dave from Barrington, IL United States  


Was this review helpful to you?

View All Customer Reviews