Return to Heating Element Kit, 5500 watt TC Ripple, Weldless TC, Clamp, Gasket

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 2

0 of 0 people found the following review helpful:

Nice Heating Element May 31, 2023 Reviewer: Bryan Miller from Pittsburgh, PA United States   Seems well built.  Installed nicely and seems to be working as expected after a couple trial runs with just water to tune PID loop and test boil. Was this review helpful to you?

0 of 0 people found the following review helpful:

December 31, 2021 Reviewer: Jim Sumrall from Thompsons Station, TN United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Excellent quality, clean design and good quality September 11, 2020 Reviewer: Benny Stetson from FORT BELVOIR, VA United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Must have for electronic brewing July 10, 2020 Reviewer: Josh Brockett from Clovis, CA United States   I ordered 2 of these to upgrade my Keggles. One went into my HLT and the other in my Kettle. My HLT I have to fill up to 14g to completely submerge my HERMS coil. With my brew commander (bought from brew hardware *****) and 240V power it heated that water in the HLT and my mash water recirculating through the HERMS, to 168f in 1h15min. That’s fast! If I add a whirlpool to the HLT I’m sure it will be faster (45-50min). When I transferred the wort to the kettle the temp was around 165f. The element heated to a boil in 20min. Cleaning is easy either leave in place and heat up PBW or simply slide it out and scrub it for a deep clean. Installation was easy make sure you pick a flat surface on the pot drill you hole and the bulkhead I held by hand and I also purchased the 52mm socket and tightened from the inside by hand. No leaks! Highly recommended Was this review helpful to you?

1 of 1 people found the following review helpful:

Best investment I've made September 23, 2018 Reviewer: Andrew Schanhofer from Sparta, WI United States   I brew 10 gal batches in kegs and burn through a ton of propane. After realizing I could add 2 30 amp outlets (1 for boil, 1 for HLT in a HERMS system) and go electric, I bit the bullet and did it. I will never go back to propane, these things are insane. Tap water comes out at 70, up to 160 for strike water in 15 minutes(8-9 gal). From sprage temp (~150) to boil in just under 20 minutes (12gal). Awesome rolling boiling, and no leaks at all. Do yourself a favor and get the carbide bit and socket to tighten, worth the extra money for how easy everything goes once its drilled and sealed. Saved at least an hour of waiting time between heating up strike/sprage water and boil kettle wort, more than worth the money. Was this review helpful to you?

1 of 1 people found the following review helpful:

hot fast June 1, 2018 Reviewer: Benzo from Cleveland OH   only had 1 brew session with these so far but amazed at how fast they heat up your water. keeps a clean look on the outside of the kettle with the TC connection. just working on the best way to clean it. Was this review helpful to you?

1 of 1 people found the following review helpful:

Awesome! No Leaks! May 28, 2018 Reviewer: Robert Mcclain from Ponte vedra beach, FL United States   The weldless TC fitting is probably the coolest invention ever for the homebrewer. I have zero knowledge or time to learn how to weld and would never be able to go all electric without this thing. So Simple. Was this review helpful to you?

0 of 1 people found the following review helpful:

High quality April 29, 2018 Reviewer: DC from Noblesville, IN United States   Excellent quality, complete kit. Was this review helpful to you?

2 of 2 people found the following review helpful:

Fantastic installation kit October 31, 2017 Reviewer: Jarrod from Vancouver, BC   This kit installed with east, sealed perfectly and did exactly what I needed. Very happy with how this turned out on my kettle. Was this review helpful to you?

0 of 0 people found the following review helpful:

GREAT!! October 4, 2017 Reviewer: Scott D from Batavia, IL United States   This is great. A fairly easy to remove heating element so you can actually get in and clean them and not have it in the way when cleaning the kettle. Perfect! Was this review helpful to you?