Return to Spincycle Submerge Weldless Low Port Kettle Whirlpool Return

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 2

0 of 0 people found the following review helpful:

February 18, 2019 Reviewer: Bob G from Fort Wayne, IN United States   What a nice piece. Hugs the side of the kettle so as not to interfere with my IM chiller. Was this review helpful to you?

0 of 0 people found the following review helpful:

Better than expected January 18, 2019 Reviewer: Lucas Gray from Ames, IA United States   Installed on a bottom drain keggle expecting to get a mediocre whirlpool with my Chugger pump, I was happily surprised when this performed better than the tangential inlet I had on my old kettle. Was this review helpful to you?

0 of 0 people found the following review helpful:

Exactly as advertised June 24, 2018 Reviewer: JH from FL United States   Great product. Was this review helpful to you?

0 of 0 people found the following review helpful:

Two thumbs up March 10, 2018 Reviewer: Todd Umphrey from Linwood, MI United States   If you’re looking for a weldless recirculating port or low profile whirlpool solution this is it.  I use this for my water recirculating port on my HLT HERMS system because I can turn it in any direction I want the water to return in depending on batch size.  Simple great design and a very high quality build. Was this review helpful to you?

1 of 1 people found the following review helpful:

Amazing design! October 31, 2017 Reviewer: Jarrod from Vancouver, BC   This little things sits so snug and close to my kettle wall that it does not interfere at all with the biab going on around it until it is time for it to do its job. And when its time for it to shine, oh boy does it ever! Whirlpool like the plug just got pulled! Was this review helpful to you?

0 of 0 people found the following review helpful:

Fantastic Product!!! July 28, 2017 Reviewer: John W from MI United States   Easy to install like any other weldless addition.  Product works just like it should, and I have had no issues with it.  I am using it in my boil kettle to whirlpool during post boil hop additions and cooling.  Follow the installation directions and you will be good to go!!! Was this review helpful to you?

0 of 0 people found the following review helpful:

Spincycle Submerge in HLT March 24, 2017 Reviewer: Rob R from West Jordan, UT United States   I'm using the Spincycle Submerge in my HLT.  I have an electric HERMS system with a standalone heat exchanger.  During system startup I use both the heating element in my HLT and the heat exchanger to heat my strike water.  I recirc from HLT to Pump to HEX back to HLT.  The Spincycle Submerge provides a safe secure way to plumb my return line.  Prior to this, I would simply hang the return hose over the top of the HLT.  One time the hose fell out and resulted in pumping my HLT dry and damaging the HLT's heating element.  Coupling the Spincycle Submerge with a ball valve and a camlock fitting means I don't ever have to worry about that happening again.  The whirlpool motion helps avoid temperature stratification inside my HLT.  It installed easily and is leak-free.  If I didn't already have a whirlpool arm in my BK, I would have ordered a second Spincycle for it. Was this review helpful to you?

0 of 0 people found the following review helpful:

Great addition to my brew pot February 23, 2017 Reviewer: Richard Jenkins from Edison , NJ United States   Easy install.  low profile inside pot. Works great for cooling and trub control. Good stuff. Was this review helpful to you?

0 of 0 people found the following review helpful:

This Fitting Changed my Life January 30, 2017 Reviewer: Anonymous Person from Freeport, ME United States   I brewed my first batch yesterday with this whirlpool fitting in my boil kettle.  The addition cut my cooling time in half, and the beer going into the fermentor was super clean.  This is a much easier way of doing things than trying to generate a good whirlpool with a spoon or paddle. Was this review helpful to you?