Home > Equipment > Keg, Pot, Cooler Parts > Bulkheads >

Spincycle Weldless Kettle Whirlpool Return
Spincycle Weldless Kettle Whirlpool Return


 
Alternative Views:


Our Price: $31.00

Quantity in Stock:62

Product Code: SPINCYCLE


Spincycle Kettle Type:


Whirlpool Options:


Qty:  
Description
 
Brewers that use immersion chillers and also own a pump should know that recirculating the wort back into the kettle to whirlpool the wort makes for much faster cooling and will also make a concentrated pile of trub and hop particles in the center of the kettle bottom. This whirlpool port assembly installs high up on your kettle wall above the typical wort level and then extends down before curving to the side to force the recirculated liquid towards the sidewall.

Introducing the BrewHardware exclusive and purpose-built unit called the Spin Cycle. We started with our industry leading "True Bulkhead" weldless bulkhead design with captured O-ring and extended male threads and had the 1/2" drop tube fully welded in. The result is THE most compact and visually stunning way to whirlpool without the need to put a ball valve on the port (the port is meant to be installed well above the max liquid level). It includes the base unit with the welded drop tube, the captured high temp silicone oring, a thin SS washer and a 1/2" NPS locknut to hold it all together. Best of all, look at that price! You couldn't get a professional welder to tack weld two pieces of scrap together for this much.


OPTIONS:


LENGTH: The standard setup positions the output at 10" below the center of the bulkhead hole but you can also select 12" or 14". In general, the outlet height of the whirlpool is not critical. You just want to make sure it's at least 3" off the bottom of your pot and will remain at least 1" below the surface of the wort (be careful to consider all the batch sizes you will use). Note that we can also make them at drop lengths that are any length between 4" and 14". If you want a length not listed, order the next longer size and specify the length in order comments.

POT OR KEG? The drop tube sits so close to the side wall that we need to know if it's for a pot or a converted keg. Since you'll install it up nice and high, it will be on a curved area of the keg. We need to make a mild bend so that the drop tube doesn't hit the side of the keg.

ACCESSORIES:


These can be added to the cart in the Since the exterior of the pot will have 1/2" Male NPT threads sticking out, you'll have to decide how you want to attach your hose returning from the pump. Our first preference is to thread on a Camlock Type A which would be appropriate if you already have camlocks in your system. You can also use a BLQD type A if you are using that quick disconnect style. The last option would be to use a hose barb with a 1/2" NPT female thread on it. None of these are included with this unit and will be added in the accessory list on the right.

Install Notes:
Drill a clean 13/16" diameter hole in the upper sidewall of the pot, above the max liquid level line you plan to use. It is also important to remove any sharp edges or "burrs" from the inside edge of the hole, otherwise the oring can get torn. Pro Tip: If you are using a step bit to make this hole, drill most of the steps from the outside of the pot all the way up to the 3/4" size. Then drill to 13/16 from the inside of the pot to remove the sharp burr. If you have a sharp edge on the outside of the pot, it will NOT affect the interior oring seal at all. It will get covered with the SS washer anyway.

Insert the threaded portion of the unit through the hole from the inside of your pot or keg with only the oring in place. On the outside, install the metal washer and locknut and snug everything up with a wrench. You can simply hold the drop tube with one hand to keep it vertical while tightening the exterior locknut.
Note: Due to how close this assembly sits to the sidewall of the pot, be aware of any interior features that would obstruct the unit. One example is the Bayou Classic pots that have the interior rim that supports a basket. You can use the Spin Cycle in these pots but the install has to be done below the ledge rather than above it.
Customer Video
Average Rating: 5 of 5 Total Reviews: 53 Click Here to Write a Review »

Accessories
Hose Barb, 1/2" Female NPT x 5/8" Hose ID
Our Price: $4.00

Add
Hose Barb, 1/2" Female NPT x 5/8" Hose ID
Camlock Quick Disconnects - Cam A
Our Price: $4.00

Add
Camlock Quick Disconnects  - Cam A
Quick Disconnects Type A - MQD x FNPT
Our Price: $7.50

Add
Quick Disconnects Type A - MQD x FNPT
NPT Swivel Connector, Cool Touch, 1/2" Female NPT x 1/2" Hose Barb
Our Price: $8.99

Add
NPT Swivel Connector, Cool Touch, 1/2" Female NPT x 1/2" Hose Barb


  0 of 0 people found the following review helpful:
 
Awesome July 12, 2018
Reviewer: Patrick Sloan from El Paso, TX United States  
This thing worked perfectly.  I highly recommend it.  I had been using a different whirlpool arm before this.  The angle and depth of the spincycle allows a faster whirlpool creating a denser cone of trub.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
June 25, 2018
Reviewer: adam Kugler from East Syracuse, NY United States  
It works great!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
June 17, 2018
Reviewer: Brian Nichols from fraser, CO United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great piece of kit - one problem though April 19, 2018
Reviewer: Christopher S Farmer from Villa Rica, GA United States  
I purchased this to modify to function as a dip tube for my Brewer’s Edge Mash and Boil. It is probably the only item on the market that will give you the clearance to allow the grain basket to still fit in the kettle. So my only complaint is that you don’t sell one precut or made to a correct length for this purpose. Other than that this is perfect and very high quality.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Spin cycle whirlpool April 5, 2018
Reviewer: charles butler from Bronx, NY United States  
Bought it for my brewers edge mash and boil. The piece was narrow enough to allow grain tube to slide in unprohibited. I bought a 14 inch to whirlpool and a 4 inch which I modded into a dip tube. Great product!

Was this review helpful to you?

View All Customer Reviews