Home > Equipment > Keg, Pot, Cooler Parts > Kettle Whirlpool >

Spincycle Robo, Whirlpool Return for Robobrew Pumped Units
Spincycle Robo, Whirlpool Return for Robobrew Pumped Units


 
Alternative Views:


Our Price: $32.00

Quantity in Stock:22

Product Code: SPINCYCLEROBO
Qty:



The following items are included with this product:

Description
 
If you have a V3 Robobrew with the pump, you want this whirlpool. The Robobrew comes with a SS immersion chilling coil and chilling times are greatly reduced if you keep the wort stirring. You could do it with a spoon but since you already have a pump, dropping in this retrofit whirlpool will do the job for you while you kick back with a beer.

Since the V3 Robobrew's mash re circulation tube terminates up top with a female camlock, we simply TIG welded a male camlock to some custom bent 3/8" OD SS tubing that goes up, over, and then down to about the 3 gallon mark.

We've received reports of our male camlock not fully seating in some of the cam females that area preinstalled on the robobrew unit. Since we cannot anticipate when those units will be out of spec, we have decided to include a replacement type D camlock to ensure absolute compatibility. You'll just have to unthread the existing cam D off the valve and put the new one on.

Average Rating: 4 of 5 Total Reviews: 5 Click Here to Write a Review »

  1 of 1 people found the following review helpful:
 
Does not fit my Robobrew V3 March 27, 2019
Reviewer: Anonymous Person from Oakland, CA United States  
*******************
Brewhardware.com Response: We have sold 100 of these so far and the reports of non-compatibility with the Cam D that is preinstalled on the ROBO is in the single digits. This suggests that there is an issue with the Cam D where the units female/male are a matched pair but perhaps without regard to the Mil-Spec standard. We've decided to force the issue by including a new Cam D to ensure compatibility.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
February 24, 2019
Reviewer: Thomas Manning from grayslake, IL United States  
Works great, does exactly what it’s intended to do

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Great Service and it works February 16, 2019
Reviewer: Andrew Tompkins from Derbyshire, United Kingdom  
The only issue is that my robobrew v3's manifold won't lock closed onto the whirlpool attachment.  I use a cable tie to hold the locking arms together.  I understand from others that it can be machined down further until it fits properly but I don' t have the tools to do this.
It might even be improved further if the end of the pipe was restricted so that it forces the liquid out at higher velocity causing more spin.  Guess I could do this myself with a hammer!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Had the same issue with CamLock February 1, 2019
Reviewer: GregK from Cranberry Twp, PA United States  
I had the same issue with adding a connection other than the arm that came with it, I ended up replacing the Type D - Female QD Coupling to Female 1/2" NPT ($5.65)with a new one and now all my other connections fit like a charm including the arm that came with the unit.
easy fix and now I cam seamlessly connect my wert chiller or recirculation arm.
hope it helps

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
Nice but the cam fitting is too big to lock down January 25, 2019
Reviewer: John Rager from Maidens, VA United States  
It is a nice product but the cam fitting is too wide in the center and needs sanding down to allow the cam lock arms to fully close to lock it in place. I used a Dremel like tool to carefully remove enough material to allow the cam lock arms to fully close.

Was this review helpful to you?