Return to Tungsten Carbide Hole Saw, 40mm or 1-5/8 Drill Bit, for Stainless Steel

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 2

0 of 0 people found the following review helpful:

Tungsten Carb Hole Saw Works well May 31, 2023 Reviewer: Bryan Miller from Pittsburgh, PA United States   I was skeptical about a whole saw for going through the side of a standard 1/2 barrel sanke keg.  I also made things more difficult for myself by punching a 1” hole first (thinking I would use a 40.5mm punch with 3/4” draw stud - turns out, that tool/die can’t be sourced anywhere and would be almost $300 if it could actually be bought).  The whole saw worked surprisingly well.  I got three nice clean holes in my keggle, installed three weldless bulkhead fittings with no leaks.  I’m very happy with the tool. Was this review helpful to you?

0 of 0 people found the following review helpful:

Nice robust hole saw February 16, 2022 Reviewer: Pat Ward from Newfield, NY United States   Yes the math doesn't seem right at first glance (40mm=1.57"), but the idea is that after a little deburring with a file you'll have an appropriately sized hole for the 1-1/2" weldless bulkhead.  The teeth are sharp and cut in well, and are likely to grab as they get through so stay slow. Was this review helpful to you?

0 of 0 people found the following review helpful:

Works like a champ! February 11, 2021 Reviewer: Shawn from Albuquerque, NM United States   Pretty straightforward.   Insert into drill.  Line up with desired hole location.  Run drill at LOW speed.  Make hole. Done. Was this review helpful to you?

0 of 0 people found the following review helpful:

Smooth and clean September 27, 2020 Reviewer: Anonymous Person from MI   Used this after my pilot hole was made.   Watching your video a few times gave me the confidence to take a shot.  It worked well, and I am excited to be one step closer to slaying steam! Was this review helpful to you?

1 of 1 people found the following review helpful:

Wow! Buy this! It will do the job! June 27, 2020 Reviewer: Gary Russell from WAKE FOREST, NC United States   I used this to drill holes on two kettles to install TRUE Weldless 1.5" TC Triclamp Bulkhead. It worked perfectly! I recommend using cutting oil (and re-applying as needed)… slow and steady & starting with a center punch did the trick. I was impressed with how it cut through the kettle wall! Was this review helpful to you?

0 of 0 people found the following review helpful:

made a perfect hole February 16, 2020 Reviewer: Eric H from Long Island   Used it to add a weldless TC bulkhead to a spike kettle lid.  Followed provided instructions and had no issues. Was this review helpful to you?

0 of 0 people found the following review helpful:

Good Quality August 9, 2019 Reviewer: Jordan Brandt from Washington, DC United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Works great July 14, 2019 Reviewer: Jesse from MEDIA, PA United States   Was this review helpful to you?

0 of 0 people found the following review helpful:

Easier than I thought. July 6, 2019 Reviewer: Michael S from Military City, USA   Clawhammer.com referred me to BH for weld-less fitting and they had the drill bit, too. I used a dremel to make an X. I drilled a small pilot hole. Then I used 1-5/8 to make the hole. I thought I might need a drill press, but straight and slows works fine. Was this review helpful to you?

0 of 0 people found the following review helpful:

Drilling Stainless Made Easy April 28, 2019 Reviewer: James FELL from Maryville, IL United States   Was concerned about drilling my stainless steel kettle as I have not drilled stainless in the past. But the hole saw and bit made it easy. Was this review helpful to you?