|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
New DC pump
|
Economy Pump
|
This new version of the center head pump features a New FDA Approved Run Dry Carbon Bearing Material (X-Dry Run Dry Protection) and an industry first TC ports direct from the factory.
We've been welding TC flanges on to brewing pumps for years now but finally a manufacturer in the homebrew space listened to the sophisticated bunch. The flanges are part of the head casting and machined in place. No welds. Why do you want a pump with 1.5" TC ports (2" actual flange diameter) instead of threads? All the cool kids are doing it. TC definitely stays cleaner longer and is easier to clean since there is nowhere for soil to hide. The downside? More expensive connections/valves.
See options below, to the right.
Center vs. Inline" In theory, the center inlet is capable of pumping hotter liquids at faster flow rates without losing prime (as compared with the INLINE versions of the pump) but the difference is barely noticeable. It's best to consider mounting locations and plumbing configuration when deciding which head to use, but if you can accommodate the center inlet, why not"
Specs:
TRI-XCPSS-CI-1 Tri-Clover CHUGGER X-DRY TRI-XCPSS-CI-1 Tri-Clover with “Run Dry Protection”
TRI-XCPSS-CI-1 Chugger TRI-CLOVER (X-Dry Series), SS CENTER INLET Brew Pump with Molded (Not Welded) 1 1/2″ Tri Clamp Fittings. Standard 115V Motor. 1/20 HP. 316 SS Housings. Standard X-Dry Impeller with Non-Replaceable – M100 Bearing, Ceramic Washers, Silicon O-Ring, 55″ Cord with Plug. 1 1/2″ Molded Tri-Clamp Connections Tri-Clover fittings are the perfect way to bring sanitary connections, found in commercial brewing applications, to your home brew setup. Wineries and Breweries use tri clamps to provide a sanitary connections between tubing and pipes. Same pump as the CPSS-CI-1 but with FDA Approved Run Dry Carbon Bearing Material. - Run Dry Carbon Bearing
- Max Flow: 7 GPM 26.5 LPM
- Max Head: 18.6 FT 4.1 M
- Power: 1/20 HP (.04 HP) .029 KW
- Electrical: 115V 50/60HZ
- Non-Submersible
- Pump & Motor: 1.4 Amps
- Can handle liquids of 250° F
- Materials are FDA Food Compliant
Some notes on using mag drive pumps:
These are not self priming pumps. The pump head must be flooded with liquid prior to turning the pump on. The easiest way to do this is to let liquid fill the inlet hose prior to connecting it to the pump. If the pump squeels or makes loud noises, shut it down and make sure the head is full of liquid.
If you wish to regulate the flow rate, it must be done on the output side of the pump (and we do recommend putting a valve on the outlet).
Orientation: We get a lot of questions regarding the best way to mount and connect hoses to these pumps. First, we recommend mounting the pumps so the outlet faces horizontally to the right. If this is not possible, the next best orientation is output facing up. The other two options will get air trapped in the pump head and cause priming issues.
Connections: We typically use 1/2" ID silicone tubing with a 1.5" TC x 5/8" hose barb adapter . By far the most important thing is to use high flow, non-restrictive components with the least number of elbows as possible on the input side.
|
Chugger
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
chugger
|
1-1/2" Triclover (TC) with drilled and tapped NPS thread
|
2" Triclover (TC) with drilled and tapped NPT thread
|
The Chugger stainless steel headed pump represents the first affordable pump designed specifically for homebrewers.
This specific model is the 115 volt stainless steel head with front/center 3/4" Male NPT inlet.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CHugger
|
Transfer Pump
|
CHugger
|
The all new Riptide Brewing Pump
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The all new Riptide Brewing Pump
|
The all new Riptide Upgrade Kit
|
Riptide parts
|
Riptide parts
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Riptide parts
|
The Chugger stainless steel headed pump represents the first affordable pump designed specifically for homebrewers.
This specific model is the 115 volt stainless steel head with front/center 3/4" Male NPT inlet.
|
Riptide parts
|
This specific model is the 115 volt stainless steel head INLINE inlet
(both inlet and outlet are 1/2" male NPT).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Chugger pump represents the first affordable pump designed specifically for homebrewers.
This specific model is the 115 volt plastic (polysulfone) head INLINE inlet (both inlet and outlet are 1/2" male NPT)
|
Chugger MAX 1/8HP Stainless
|
Chugger MAX 1/8HP Stainless
|
Chugger Parts
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chugger Parts
|
Chugger Parts
|
Chugger Parts
|
Chugger Parts
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Basic kit to add a plate chiller inline with your existing camlock enabled pump system
|
Basic kit to add a plate chiller inline with your existing camlock enabled pump system
|
Quick Disconnect and Silicone Connectivity kit for Inline pumps
|
Quick Disconnect and Silicone Connectivity kit for Center pumps
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Quick Disconnect and Silicone Connectivity kit for Riptide Pumps
|
For Wort Voyours.
|
For Wort Voyours.
|
replacement
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Camlock and Silicone Connectivity kit for Chugger Center Inlet pumps
|
Camlock and Silicone Connectivity kit for inline pumps
|
Camlock and Silicone Connectivity kit for Riptide Pumps
|
Camlock and Silicone Connectivity kit
|
|
|
