Home > Equipment > Fittings / Camlocks / Triclover > Triclover >

TRUE Weldless 1.5" TC Triclamp Bulkhead - XL up to 1/2" Wall
TRUE Weldless 1.5" TC Triclamp Bulkhead - XL up to 1/2" Wall
 
Alternative Views:
Our Price: $27.00

Quantity in Stock:(Out of Stock)

Product Code: TC15WLF_XL
Qty:

Description
 
The 1-1/2" Triclover (TC) weldless bulkhead flange allows you to add a TC port to any tank or kettle with absolutely no welding or soldering. Just drill a hole and tighten the locknut. Done!
The flange measures 2" like all other 1.5" TC ferrules, and the overall length is just under 1". The ID is 1-3/8 just like standard 1.5" weld ferrules. The short length of this ferrule makes it possible to use ripple style heating elements and not have the foldback make contact with the ferrule. These are extremely high quality pieces machined out of 304SS and polished to perfection (except for the locknut which is cast finish 304SS. Let's repeat this since we get the question constantly. YES! Ripple style elements fit into these with NO PROBLEM at all when using the ETC3 Hot Pods as the element housing/adapter.

The silicone O-ring is included and gets captured in a groove like our other True Bulkheads.

THIS IS THE XL version that can accommodate wall thickness of up to 1/2". We also have a slightly cheaper, more compact option if your wall thickness is less than 1/4".

Installation Notes:
  • Hole Size Required - 1-5/8" or 41mm. Note that the most pleasant tool to use for this is a knockout punch set. Since they are extremely cost prohibitive, the next best option is our tungsten carbide hose saw (40mm). After deburring the 40mm hole, the result is a clean 41mm hole. See the accessories column on the right for the bit.
  • The oring contact is on the flange side of the fitting so make sure there are no burrs on that side of the hole.
  • The lock nut hex measures 2-1/16" or 52mm. Turning it with an adjustable wrench does NOT work well. You'll need a socket or a box wrench. Since these tools are very rare, we offer a socket as an accessory. It requires a 1/2" drive ratchet.
  • The front of the flange does not have flats for a wrench. The easiest way to hold the front of the flange for tightening is to clamp any other TC part on with the gasket and clamp (a blank cap works great). Once tight, you can insert a long rod or screw driver into the hole of the wingnut.

We've tested this on a pot measuring as small as 12" in diameter. Anything smaller may work but we don't know for sure. Larger diameters or flat areas are no issue at all.


Accessories
1.5 TC Clamp 52mm Socket Tool for Weldless 1.5" TC Bulkhead Tungsten Carbide Hole Saw, 40mm or 1-5/8 Drill Bit, for Stainless Steel 1.5 TC Silicone Gasket (Heat Resistant to 400F)
Our Price: $7.59

Add
Our Price: $15.00

Add
Our Price: $19.00

Add
Our Price: $2.00

Add
1.5 TC Clamp 52mm Socket Tool for Weldless 1.5" TC Bulkhead Tungsten Carbide Hole Saw, 40mm or 1-5/8 Drill Bit, for Stainless Steel 1.5 TC Silicone Gasket (Heat Resistant to 400F)

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 1 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 Great product! Wednesday, December 5, 2018
Reviewer: Christopher R. from Winston, NC United States  
Easy to install and sealed first try. Low profile and very sexy looking on my kettles! Great product by a great company!

Was this review helpful to you?



Buon Vino Super Jet Filter Pads - 3-pack Fine (Number 2) $6.99
Anvil Foundry System 6.5 Gallon Electric System $385.00
Crystal 10L (Caramel Malt), Briess LB (similar to CaraHell) $2.48
BRY-97 American West Coast Ale Dry Yeast 11 g $3.84
Keg Lube, 1 oz $3.49
RIMS Hardware Kit 18" Body Length - 1/2" Male NPT I/O Ports $158.00
1.5 TC x 3/8" Female NPT THREADS Adapter $10.75
Beer Bottle Brush $3.89
Fermonster Lid Wrench $3.79