Home > Equipment > Keg, Pot, Cooler Parts > False Bottoms / Filters >

Elbow Connector for Domed False Bottoms
Elbow Connector for Domed False Bottoms
 
Alternative Views:
Our Price: $13.00

Quantity in Stock:2

Product Code: FBELBOW
Qty:

Description
 
You don't have to settle for the barbed elbow connector that comes with all the domed false bottoms out there. If you bought a domed false bottom from somewhere and found out that the inside diameter of the barb is a pathetic 1/4", this is your solution. Take a look at the comparison picture. You'll want to use a short piece of 1/2" ID silicone tubing to make the connection from this fitting over to your bulkhead fitting and that bulkhead needs at least a 1/2" barb.

This fitting fits into domed false bottoms with a 7/8" center hole.

Accessories
True Weldless Bulkhead - With Large BARB Silicone Tubing, Made in USA, 1/2" ID x 3/4" OD (1/8" Thick Walls) PER FOOT
Our Price: $15.00

Add
Our Price: $2.85

Add
True Weldless Bulkhead - With Large BARB Silicone Tubing, Made in USA, 1/2" ID x 3/4" OD (1/8" Thick Walls) PER FOOT

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 10 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 March 17, 2021
Reviewer: Anthony Neal from Asheville, NC United States  
Always top notch! Excellent products, excellent service

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Check your depth January 15, 2019
Reviewer: Brian from OH  
Lay a straight edge across the bottom of false bottom and confirm you have an air gap between pickup and straight edge.
I purchased to replace the tiny little stainless barb that comes with typical false bottom conversion.  I replaced the original false bottom barb and filled mash tun with water to check that the bulkhead (also purchased the True bulkhead barb) for leaks.  All good!  I opened the valve to drain and only a trickle of water!  After some head scratching I determined that the pickup was basically flat against the bottom of cooler.  I removed the washer to create a 1/8 inch gap and flow was restored!

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 You Need This In Your Mash Tun July 18, 2016
Reviewer: Andrew Tucker from Waterford, MI United States  
I had a false bottom from another retailer in my 10 gallon beverage cooler mash tun for many years that had the 1/4" elbow fitting on it and that wasn't an issue for me when I was lautering via gravity, but, when I put that false bottom into a kettle to do direct-fired recirculating mashing, the restriction of that elbow (as well as the bulkhead/ball valve combo) was very apparent and became a problem. I swapped the elbow on the false bottom out for this one and put a true weldless bulkhead with large barb on the pot and have zero issues recirculating and lautering with a pump. I highly recommend this little piece of the flow puzzle. Cheers!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect fit February 7, 2016
Reviewer: Phil Beno from Brooklyn Hts, OH United States  
Went from a 1/4" ID to this 5/8" ID hose connection. Mash out went quicker without getting a stuck sparge. Another quality product.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 All Grain October 15, 2015
Reviewer: Carl Noble from Tell City, IN United States  
This is the way to go! Great flow.

Was this review helpful to you?

View All Customer Reviews


Campden Potassium Metabisulfite Tablets 100 tablets $4.39
Beer Thread Low Profile 90 (5/8" BSP Street Elbow) 304SS $9.99
Heating Element, 31G Slingblade, 1.5" TC INTEGRATED 5750w $135.99
Nectaron (NZ) Hop Pellets, OZ $3.84
Priming Sugar Corn Sugar Dextrose 1 oz $0.28
Acid Blend 2 oz $2.42
Universal Stopper Intermediate - SOLID $1.50