Return to Install Tool (pull through flaring) for 1.5" TC Weld Ferrules

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 2

0 of 0 people found the following review helpful:

1.5" Triclamp Tool on a Beer Keg July 4, 2023 Reviewer: Robert Fontaine from Canuckistan   You are going to want to increase your hole size a bit over recommended for a thin pot and definitely use properly sized wrenches as it is a bear to drive through the steel of a Beer Keg but it is doable and it's never coming out.     A little silver solder for luck and you are done. Was this review helpful to you?

0 of 0 people found the following review helpful:

Awesome March 31, 2023 Reviewer: L from , NC United States   Does what it it does like a boss!! Was this review helpful to you?

0 of 0 people found the following review helpful:

Great way to add tri-clover! May 2, 2022 Reviewer: John Waggoner from Clinton Township, MI United States   The video was perfect on how to use the tool to install ferrule.  There is another video on how to do the silver solder that was very helpful as well!  The tool is well made and it was easy to use.  I have completed 2 installs so far and have one more to go! Was this review helpful to you?

0 of 0 people found the following review helpful:

April 27, 2022 Reviewer: Odin Anderson from Bellevue, WA United States   Was this review helpful to you?

1 of 1 people found the following review helpful:

Fantastic! December 23, 2020 Reviewer: Jeff McClain from Nampa, ID   I can't say enough about how well this tool works for putting 1.5" TC fittings into your kettle.  I normally pull through from inside out to dome it out and then pop the ferrule back out and pull it in from the correct side.  This leaves a VERY nice domed fillet inside that fills with solder and make a smooth curved application that scrubs up nice with barkeeps friend. Was this review helpful to you?

0 of 0 people found the following review helpful:

Worked perfectly August 9, 2020 Reviewer: Chris Billingsley from Round Rock, TX United States   I’ve been waiting for this to come back in stock and boy was it worth the wait!! Super easy to use gave me the ability to put 1.5” tri clamp fitting on my HLT and boil kettle for my electric elements. Was this review helpful to you?

0 of 0 people found the following review helpful:

Fantastic March 8, 2020 Reviewer: Christopher Hamilton from Satellite Beach, FL United States   As always, never disappointed with Brewhardware.  Very intuitive design and very cost effective when compared to alternatives.  It's at a point now where I'm tempted to replace all fittings on my kettles with 1.5 TC connectors! Was this review helpful to you?

0 of 0 people found the following review helpful:

Everything is true March 4, 2020 Reviewer: Eric from Broomfield, CO United States   I'm so impressed. This tool/technique is just fantastic. I've been looking for a good sanitary tig welder, for years, and every time I find one, they make enough money and are busy, it's hard to get a fitting put on. Now I feel like I can make the gear, I want. Totally custom. You need to do careful work, but it's very straightforward. It's a game changer for me! Way to go Bobby. Was this review helpful to you?

0 of 0 people found the following review helpful:

Pull through flaring for 1.5 inch tri-clover February 9, 2020 Reviewer: Allan Authier from Wallaceburg, ON Canada   Worked amazing ! Now I need to get the 1/2 inch one also. Was this review helpful to you?

1 of 1 people found the following review helpful:

worked like a charm! July 27, 2019 Reviewer: Jared Lazorchak from Galeton, PA United States   I flared the kettle outward and then pressed  my 1.5" ferrule into opening and worked very nicely and looks great. Was this review helpful to you?