Home > Equipment > Keg, Pot, Cooler Parts > Thermometers >

Weldless Probe Compression Fitting for pots/kegs PCOMP4
Weldless Probe Compression Fitting for pots/kegs PCOMP4
 
Our Price: $15.00

Quantity in Stock:13

Free Shipping
Product Code: PCOMP4
Qty:

Description
 
If you want to insert a narrow digital thermometer probe into a hole in your kettles or coolers or into a threaded fitting such as a tee or a coupling welded into your vessel, here's how to do it.

This specific item is PCOMP4 - Weldless 1/4" NPT on one end and probe compression on the other. This fitting uses a custom machined weldless bushing and is not made from makeshift parts.

NEW IMPROVED DESIGN! Our latest version of this PCOMP4 fitting features a machined groove in the body of the fitting to capture a silicone ORING rather than relying on a flat gasket that may roll out of position if overtightened. With the new captured oring design, it's impossible to overtighten the fitting.

General Info for all these types of fittings:


This series of fittings have 1/2" OR 1/4 male NPT on one end and will accept from .19" to a .25" diameter probe (see notes). The included orings make a leak free connection. PCOMP1 and PCOMP2 are thread in fittings so you'd use them for creating in-line temperature assemblies using a tee or similar. PCOMP3 and PCOMP4 are weldless versions. Read more below.

Types Available:


PCOMP1 - 1/2" Male NPT to Narrow Probe: If you want to insert the CDN Proaccurate thermometer or a right-angle probe that comes with remote kitchen thermometers. The range of probe diameters supported with this fitting is 1/8" to 1/4". This can be used for both the handheld/remote probes as well as 1/4" capsules like the A419 controller sensors.
PCOMP2 -1/4" Male NPT to Narrow Probe: This version is specifically offered to thread into the open end of the tee in the WLSTNT kit to add digital or remote temperature functionality instead of threading a dial thermometer in. Again, this one is 1/4" NPT male threaded. There is no picture of this option on the page. You can also make this weldless by also adding the 1/4" make weldless kit below. This one only supports probe diameters of up to 3/16" but can be modified for A419 (1/4" OD) probes by drilling the fitting out with a 1/4" drill bit.
PCOMP3 -1/4" Male NPT to Narrow Probe with extended weldless bulkhead for cooler walls up to 1.25" thick.Install notes on this one: Drill a 1/2" hole all the way through both walls of the cooler. Open up the hole in the outside skin of the cooler to about 3/4 and chip out the foam insulation a bit to reveal a clean interior wall surface. The bushing and metal washer insert from the inside. The red gasket gets pushed over the bushing from the OUTSIDE of the inner wall. It's tricky to get it on, but that's how it's designed. Now insert the compression fitting/coupling down into the hole and thread the bushing into it by turning it from inside the cooler. A little tighter than hand tight is enough to create the seal against the gasket.
PCOMP4 -1/4" Female NPT to Narrow Probe with Weldless Parts- Buy this option if you just want to drill a 1/2" (up to 9/16" would be OK) hole in your thin-wall vessel and install a narrow probe thermometer. This is the most economical way to do it.





Note, if you're installing the CDN DTQ450 using option 4 into a direct heated vessel, we highly recommend clipping our HS.SM heatshield onto the fitting to protect the thermometer from intense heat. See accessories below.

Instructions for installing a thermometer into any of these fittings: Once you have the fitting installed into your flow or into your vessel, remove the compression nut from the fitting and place it over your thermometer probe with the open threaded end towards the point. Push the two included red orings over the probe and then insert the probe into the compression fitting. Thread the compression nut onto the fitting to sandwich the orings. Hand tight is generally enough to create a seal. Do not overtighten with a wrench more than one additional turn past hand tight.


Warning!! While the Orings will keep their seal on the probe and allow you to slide the probe while there is liquid in the vessel, obviously you have to be extremely careful that you do not pull the probe all the way as these fittings are not self sealing.

Accessories
CDN Clock/Timer/Corded Digital Thermometer DTTC CDN Digital Thermometer DTQ450X Silicone Orings (PAIR) for Probe compression fittings (Pcomp) Gasket
Sale Price: $17.99

Add Free Shipping
Our Price: $17.00

Add Free Shipping
Our Price: $1.50

Add Free Shipping
CDN Clock/Timer/Corded Digital Thermometer DTTC CDN Digital Thermometer DTQ450X Silicone Orings (PAIR) for Probe compression fittings (Pcomp) Gasket

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 11 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 March 15, 2022
Reviewer: Anonymous Person from , NE United States  
Exactly what I was looking for. Easy install & works great. Thanks

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Quality Hardware December 28, 2020
Reviewer: Ralph Fain from Crawfordsville, IN United States  
This is a great weldless fitting for adding a digital thermometer or temperature probe to a boil kettle, mash tun, or HLT. Top notch quality as always from BrewHardware

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Good quality product & fast service April 14, 2018
Reviewer: Elliott Silkowski from wilkes-barre, PA United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 December 22, 2017
Reviewer: guy hernandez from Brooklyn, NY United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Easy to install and very effective November 9, 2017
Reviewer: Kevin Miller from Doylestown, OH United States  
I was setting up an electric boil kettle and needed a fitting to hold the k-type temperature probe. These are very well made, fit nicely, and do not leak.

Was this review helpful to you?

View All Customer Reviews