Return to Elbow Connector for Domed False Bottoms

Sort By:: Most Helpful Newest Rating: High to Low Rating: Low to High	Page of 1

0 of 0 people found the following review helpful:

March 17, 2021 Reviewer: Anthony Neal from Asheville, NC United States   Always top notch! Excellent products, excellent service Was this review helpful to you?

0 of 0 people found the following review helpful:

Check your depth January 15, 2019 Reviewer: Brian from OH   Lay a straight edge across the bottom of false bottom and confirm you have an air gap between pickup and straight edge. I purchased to replace the tiny little stainless barb that comes with typical false bottom conversion.  I replaced the original false bottom barb and filled mash tun with water to check that the bulkhead (also purchased the True bulkhead barb) for leaks.  All good!  I opened the valve to drain and only a trickle of water!  After some head scratching I determined that the pickup was basically flat against the bottom of cooler.  I removed the washer to create a 1/8 inch gap and flow was restored! Was this review helpful to you?

1 of 1 people found the following review helpful:

You Need This In Your Mash Tun July 18, 2016 Reviewer: Andrew Tucker from Waterford, MI United States   I had a false bottom from another retailer in my 10 gallon beverage cooler mash tun for many years that had the 1/4" elbow fitting on it and that wasn't an issue for me when I was lautering via gravity, but, when I put that false bottom into a kettle to do direct-fired recirculating mashing, the restriction of that elbow (as well as the bulkhead/ball valve combo) was very apparent and became a problem. I swapped the elbow on the false bottom out for this one and put a true weldless bulkhead with large barb on the pot and have zero issues recirculating and lautering with a pump. I highly recommend this little piece of the flow puzzle. Cheers! Was this review helpful to you?

0 of 0 people found the following review helpful:

Perfect fit February 7, 2016 Reviewer: Phil Beno from Brooklyn Hts, OH United States   Went from a 1/4" ID to this 5/8" ID hose connection. Mash out went quicker without getting a stuck sparge. Another quality product. Was this review helpful to you?

0 of 0 people found the following review helpful:

All Grain October 15, 2015 Reviewer: Carl Noble from Tell City, IN United States   This is the way to go! Great flow. Was this review helpful to you?

0 of 0 people found the following review helpful:

Works as advertised!! June 15, 2015 Reviewer: Anonymous Person from Oceanside, CA United States   Works as advertised!! Was this review helpful to you?

0 of 0 people found the following review helpful:

No more stuck mashes May 5, 2015 Reviewer: Jeremy Blynt from Abington, PA United States   I searched and searched the internet for an elbow that with 1/2" barb and 1/2" NPT. This is the best solution I found. The secret is it's not really a 1/2 barb. It's actually larger than that. Looks to be a 1/2" male threads that have been machined down to allow a hose to just stretch over the machine end. It's a tight fit, but made a great seal. Along with upgraded ball valves, this elbow has given my cooler mash tun a new life without the stuck mashes that added hours to my brew days. Was this review helpful to you?

0 of 0 people found the following review helpful:

Quality and complete March 2, 2015 Reviewer: Dennis Kamfonik from Mendon, MA United States   The guess was taken out by this set. I was looking for a full flow fitting to add to by false bottom. Great solution that fit perfectly. Much better than the 3/8" fittings being offered by others. Was this review helpful to you?

0 of 0 people found the following review helpful:

Great Upgrade February 23, 2015 Reviewer: Troy E. from Stafford, VA United States   This will be a big improvement over elbow that came standard with the false bottom I currently have Was this review helpful to you?

0 of 0 people found the following review helpful:

Works great December 15, 2014 Reviewer: Erik Rottier from Appleton, WI United States   Used with a converted HD 10 gallon cooler MLT. I upgraded everything else to 1/2 inch, so it only makes sense to upgrade this as well. It installs in minutes and is definetly a high quality product. Was this review helpful to you?