Return to True Weldless Bulkhead - With Female Threads
Sort By::
Page of 2
Click to see more items


  0 of 0 people found the following review helpful:
 
5 of 5 Excellent product, but... March 7, 2024
Reviewer: Anon Ymous  
The item description could be a little better. I was expecting female NPT threads on both ends. However this product only has female threads on one end, and 1/2" NPT (without the taper) threads on the other side.

I installed this into a vessel with a 28" diameter. No leaks!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Great product May 17, 2022
Reviewer: Kelly Wingert from NEVADA, MO United States  
The best weldless bulkhead I've bought. No leaks

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 August 4, 2021
Reviewer: Anonymous Person from Lafayette, NJ United States  
The first MLT I built was done the off the shelf way as the video puts it - pipe nipple, washers, o-rings, etc. Never fully sealed and ended up using food-grade silicone to seal it. Used this on my new Home Depot 10 gal. MLT and in 5 minutes had it installed and with a perfect seal.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 July 23, 2020
Reviewer: Sean Powers from Columbus, OH United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Worked perfect! May 20, 2019
Reviewer: Thomas Rogers from Saugus, MA United States  
Used on my 10 gal Rubbermaid mash tun.  Slid right into existing hole and no leaks.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Just what I needed also April 7, 2019
Reviewer: Josh from APO, AP United States  
I was installing a HERMs coil and I drilled a hole in the side of my kettle just a little too big, it's pretty easy to go just a tiny bit too big with the step drill so after install my pot was leaking. I tried washers and I tried high temp silicone but still had a small leak. This closed the gap perfectly with the extra size up centering ring. The HERMs coil threads fit right into the female side on the inside of the kettle and no leaks.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Exactly what i needed February 5, 2018
Reviewer: John from VT  
I was really hoping I could put the female end on the outside of the ss brewtech mash tun; however I needed to drill a bigger hole.  But its the only thing that has worked so far for fitting a blichmann autosparge into the mash tun.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Works like a champ January 28, 2018
Reviewer: Mitch Cumstein from NorCal United States  
No leaks, no problem. A fantastic mate with a Lowe's Igloo mashtun

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 No leaks November 21, 2016
Reviewer: Derek G. - Guggman Haus Brewing from Indianapolis, IN United States  
No leaks, easy installation. Thanks again for another piece of great hardware.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect September 19, 2016
Reviewer: Kenney from Prescott, AZ United States  
These weldless bulkheads are the best.Bought several,no leaks first time tightning. Buy with confidence,you wont be sorry.

Was this review helpful to you?

   
  Click to see more items