Hot Pod Kettle Element Enclosure 2ETC3 2" TC enclosure, clamp and gasket

Home > Equipment > Electric Brewing > Kettle Element Enclosures >

Our Price: $48.00

Quantity in Stock:5

Product Code: 2ETC3

Qty:

Description

Electric Kettle Enclosure with 2" TC flange, gasket and clamp.

This specific unit features an enclosure with a 2" TC (triclover) flange welded. It assumes you already have a 2" TC flange welded to your vessel . We have other kits with variious accessories included elsewhere on this site.

General info for all TC (triclover) based electrical enclosures:

The matter of enclosing the electrical connection of your heating element has long been the shortcoming of many Do-It-Yourself element installs. Many solutions relied on "potting" the exposed connections with silicone or epoxy which was a bit more permanent than practical. In addition to shielding the connections, another challenge is providing an earth ground point on the metal pieces. Our design solves both of these problems in an aesthetically pleasing and functionally adequate way. We have several options depending on whether you want to weld, solder or use gaskets to install your heating elements.

What's included with all enclosure options:

Screw-together canister with ground screw and cord grip.
Electrical Connection Parts: One pair of crimp-on ring terminals to connect your cord (up to 10 gauge wire) to the element, and a single ring terminal to attach an earth ground to the canister, a couple pieces of shrink wrap tubing (shrink it over your crimp terminals with a lighter).

Note!! electric heating element is NOT included with ANY of these kits.

The cord grip included with this kit will accommodate nearly any practical cord diameter from 14/3 SJ to 10/3 SJ cords.

Accessories

Heating Element, Threaded, 1650 watt, 120v, All Stainless Steel

Heating Element, 5500 watt THREADED, All Stainless Steel

Our Price: $29.00

Add

Our Price: $39.00

Add

Average Rating: Average Rating: 4 of 5

4 of 5 Total Reviews: 5 Click Here to Write a Review »

0 of 0 people found the following review helpful:

Outstanding	March 3, 2022
Reviewer: Joe P from MD United States

Outstanding item works perfectly I wouldn't hesitate to buy again

Was this review helpful to you?

0 of 0 people found the following review helpful:

Work ok.	October 26, 2021
Reviewer: CH Perdue from Peyton, CO United States

It fit the element good. The only reason I gave it 4 stars is the rear screw on enclosure is less than perfect. I had to drill 2 opposite small holes to keep the rear cover secure while I move the boil pot. I used 2 #4 sheet metal screws and it seem to be holding.

Was this review helpful to you?

0 of 0 people found the following review helpful:

Haven't used it yet	March 12, 2016
Reviewer: Andrew Superczynski from Annapolis, MD United States

I bought this in anticipation of building a RIMS setup, haven't got around to using it yet, but it looks like it will work out perfectly.

Was this review helpful to you?

0 of 0 people found the following review helpful:

Looks Great!	June 28, 2015
Reviewer: steve stowell from Colorado Springs, CO United States

Hot Pod is a great solution for my brewpub! It encloses the raw wiring, should make my electric inspection go well!

Was this review helpful to you?

0 of 0 people found the following review helpful:

2" TC enclosure	February 1, 2015
Reviewer: BK from PDX, OR United States

Great component. Always make sure you ground your element correctly, and this device allows you to do that. The security of a grounded element with ease of install and element change with the sealing of a tri clamp fitting.

Was this review helpful to you?

	Heating Element Kit, 5500 watt TC Ripple, Solder TC, Clamp, Gasket $109.00
	Locline, 1/2" size, Socket End Cap $2.99
	Rubber Stopper, SOLID, #2 $0.50