Home > Equipment > Keg, Pot, Cooler Parts > Thermometers >

Probe Compression Fitting 1/2" MNPT x 1/4 probe PCOMP1
Probe Compression Fitting 1/2" MNPT x 1/4 probe PCOMP1


 
Alternative Views:


Our Price: $14.00

Quantity in Stock:14


Product Code: PCOMP1
Qty:

Description
 
If you want to insert a narrow digital thermometer probe into a hole in your kettses or coolers or into a threaded fitting such as a tee or a coupling welded into your vessel, here's how to do it.

This specific item is PCOMP1 - Male 1/2" NPT thread on one end and probe compression on the other.

General Info for all these types of fittings:


This series of fittings have 1/2" OR 1/4 male NPT on one end and will accept from .19" to a .25" diameter probe (see notes). The included orings make a leak free connection. PCOMP1 and PCOMP2 are thread in fittings so you'd use them for creating in-line temperature assemblies using a tee or similar. PCOMP3 and PCOMP4 are weldless versions. Read more below.

Types Available:


PCOMP1 - 1/2" Male NPT to Narrow Probe: If you want to insert the CDN Proaccurate thermometer or a right-angle probe that comes with remote kitchen thermometers. The range of probe diameters supported with this fitting is 1/8" to 1/4". This can be used for both the handheld/remote probes as well as 1/4" capsules like the A419 controller sensors.
PCOMP2 -1/4" Male NPT to Narrow Probe: This version is specifically offered to thread into the open end of the tee in the WLSTNT kit to add digital or remote temperature functionality instead of threading a dial thermometer in. Again, this one is 1/4" NPT male threaded. There is no picture of this option on the page. You can also make this weldless by also adding the 1/4" make weldless kit below. This one only supports probe diameters of up to 3/16" but can be modified for A419 (1/4" OD) probes by drilling the fitting out with a 1/4" drill bit.
PCOMP3 -1/4" Male NPT to Narrow Probe with extended weldless bulkhead for cooler walls up to 1.25" thick.Install notes on this one: Drill a 1/2" hole all the way through both walls of the cooler. Open up the hole in the outside skin of the cooler to about 3/4 and chip out the foam insulation a bit to reveal a clean interior wall surface. The bushing and metal washer insert from the inside. The red gasket gets pushed over the bushing from the OUTSIDE of the inner wall. It's tricky to get it on, but that's how it's designed. Now insert the compression fitting/coupling down into the hole and thread the bushing into it by turning it from inside the cooler. A little tighter than hand tight is enough to create the seal against the gasket.
PCOMP4 -1/4" Female NPT to Narrow Probe with Weldless Parts- Buy this option if you just want to drill a 1/2" (up to 9/16" would be OK) hole in your thin-wall vessel and install a narrow probe thermometer. This is the most economical way to do it.





Note, if you're installing the CDN DTQ450 using option 4 into a direct heated vessel, we highly recommend clipping our HS.SM heatshield onto the fitting to protect the thermometer from intense heat. See accessories below.

Instructions for installing a thermometer into any of these fittings: Once you have the fitting installed into your flow or into your vessel, remove the compression nut from the fitting and place it over your thermometer probe with the open threaded end towards the point. Push the two included red orings over the probe and then insert the probe into the compression fitting. Thread the compression nut onto the fitting to sandwich the orings. Hand tight is generally enough to create a seal. Do not overtighten with a wrench more than one additional turn past hand tight.


Warning!! While the Orings will keep their seal on the probe and allow you to slide the probe while there is liquid in the vessel, obviously you have to be extremely careful that you do not pull the probe all the way as these fittings are not self sealing.
Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 27 Click Here to Write a Review »

Accessories
CDN Digital Thermometer DTQ450X
Our Price: $17.00

Add
CDN Digital Thermometer DTQ450X
Silicone Orings (PAIR) for Probe compression fittings (Pcomp) Gasket
Our Price: $1.50

Add
Silicone Orings (PAIR) for Probe compression fittings (Pcomp) Gasket
CDN Clock/Timer/Corded Digital Thermometer DTTC
Sale Price: $17.99

Add
CDN Clock/Timer/Corded Digital Thermometer DTTC


  0 of 0 people found the following review helpful:
 
5 of 5 August 2, 2022
Reviewer: David W. from VA United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Added to the output end of my CFC. February 11, 2021
Reviewer: Bruno from Surprise, AZ United States  
This works perfectly at the output of my CFC . It allows the use of a removable thermometer which makes cleanup easy.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Inline temp readings where you want it September 20, 2020
Reviewer: Rich W. from San Diego, CA United States  
This is the best solution for seeing what your wort temp is when coming out of the mashtun for recirculation. I have a ss tee fitting and compression fitting coming off the mashtun valve and going into a herms tube. I also did the same setup to check the temp coming into the mashtun from the herms. This way I can see the temp difference and adjust the herms water to nail my mash temps.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 July 2, 2018
Reviewer: John K. from HARRISBURG, PA United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Fittings work as expected April 23, 2018
Reviewer: Anonymous Person from Freeburg, IL United States  


Was this review helpful to you?

View All Customer Reviews