Home > Equipment > Keg, Pot, Cooler Parts > Bulkheads >

Diptube (High Flow) for Edge Pickup
Diptube (High Flow) for Edge Pickup


 
Alternative Views:


Our Price: $17.00

Quantity in Stock:205


Product Code: DIPTUBE_EDGE
Qty:

Description
 
If you bought a pot with a welded coupling for the drain ball valve, installing this diptube on the inside will help you drain most of the liquid out and this new version will get amazingly close to the sidewall of the pot to avoid most of the trub (especially if you whirlpool).

Options:
The base item inclues the 5/8" OD tube bent at a 135 degree angle, the retaining nut with 1/2" Female NPT, and a sealing oring. You will select this unit if you have MALE threads on the inside of your kettle. This configuration will also work with our TrueBulkheadMale unit.

If your kettle has 1/2" FEMALE NPT threads on the inside YOU WILL ALSO NEED TO PURCHASE the Premium Hex Nipple as shown in the accessories on the right. It works best if your female threaded port is flush with the inside wall of the kettle. This gets the open end of the tube right in to the corner.

MAY NEED TRIMMING in some pots. The main picture shows the unit installed in a 15 gallon BrewBuilt pot (about 16" diameter) and it did not need trimming.

Note that the tubing portion of this diptube is really big. The OD is 5/8" and the ID is 9/16" for superior flow compared to all the other "maximizers" you find available.

If you need a replacement oring for this unit, it's the one listed as an accessory on the right.


Does it fit the Anvil Foundry? Yes it does. The picture below is in the 6.5 or 10.5 units but it also fits the 18.



Accessories
Silicone Oring, Replacement for BLQD True Weldless Bulkhead - With 1/2" NPT Male Threads Hex Nipple, 1/2" NPT PREMIUM LOOSE
Our Price: $0.65

Add
Our Price: $16.00

Add
Our Price: $5.99

Add
Silicone Oring, Replacement for BLQD True Weldless Bulkhead - With 1/2" NPT Male Threads Hex Nipple, 1/2" NPT PREMIUM LOOSE

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 27 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 June 11, 2024
Reviewer: Alan Crauthers from Hubbard, OR United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Works and fits great April 6, 2023
Reviewer: Robert Rutledge from West Jordan, UT United States  
I used this in a rebuild of my hot liquor tank.  Pot was a 15 gallon Megapot fitted with a Spike 3-piece valve and a stainless nut as a DIY weldless setup.  The edge pickup installed easily on the exposed male threads of the Spike valve.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Great mod for Anvil Foundry 10.5 July 27, 2022
Reviewer: Derek from NH United States  
I like how close it fits to the side, should help keep the whirlpool crud in the middle while draining.  still leaves a fair amount of wort in the Anvil (~1/2 gallon), so account for that in your recipe.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Sucks the kettle dry December 16, 2021
Reviewer: Ron from Lancaster, CA United States  
This does a great job taking the wort without the trub. Make sure you buy a nipple for a typical 1/2" NPT fitting to mate the female threads on the kettle to the female threads on this pickup.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect November 4, 2021
Reviewer: Ryan Mooney from Neptune, NJ United States  
I bought this for my Gas One 10 gallon kettle that I bought off of Amazon. The dip tube fit perfectly in the kettle and is very high quality, with a nicely sized ID. It sits just a few millimeters away from the wall of the kettle. I have not used it yet, but looking forward to brew day so I can try it.

Was this review helpful to you?

View All Customer Reviews