Home > Equipment > Kegging Parts >

Ball Valve, 1/4" NPT to 1/4" MFL with Check
Ball Valve, 1/4" NPT to 1/4" MFL with Check
 
Our Price: $8.99

Quantity in Stock:126

Product Code: BV14CHECK
Qty:

Description
 
Use this to make your gas distribution manifold or an inline shut off valve. One side has 1/4" NPT right hand thread and the other side (output) has a male flare. To connect a hose, you would use a swivel flare hose barb and be sure to use a flare gasket. See accessories on the right.

Accessories
Flare Washer, 1/4 Nylon Swivel Flare Adapter - 1/4" FFL x 3/8" OD hose barb Hose Barb, 1/4" Female NPT x 1/4" Hose ID Swivel Flare Adapter - 1/4" FFL x 1/4" OD hose barb
Our Price: $0.25

Add
Our Price: $2.95

Add
Our Price: $3.00

Add
Our Price: $1.89

Add
Flare Washer, 1/4 Nylon Swivel Flare Adapter - 1/4" FFL x 3/8" OD hose barb Hose Barb, 1/4" Female NPT x 1/4" Hose ID Swivel Flare Adapter - 1/4" FFL x 1/4" OD hose barb
Swivel Flare Adapter - 1/4" FFL x 5/16" OD hose barb
Our Price: $1.99

Add
Swivel Flare Adapter - 1/4" FFL x 5/16" OD hose barb

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 9 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 April 18, 2026
Reviewer: TIMOTHY WEDDLE from ANTIOCH, TN United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 May 3, 2023
Reviewer: Jacob Schray from Wind Gap, PA United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Good insurance April 22, 2022
Reviewer: Janet Piez from New York, NY United States  
These ball valves added to a distributer are good insurance against an unused DQ leaking from the poppet. In the unlikely event that you attempt to put a liquid DQ onto the gas post (not that I would do such a thing),  the valve would prevent the mess from getting completely out of hand. Good products plus the usual amazing customer service equals a happy customer!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 REBBREWER May 31, 2020
Reviewer: TED from IRONDEQUOIT, NY United States  
The 1/4'' ball valve I ordered from BrewHardware, works very good on my taprite CO2 regulators.

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 Added to the regulator January 19, 2020
Reviewer: Edward Gierlach from Dacula, GA United States  
Upgrading my gas lines to the 4mm ID EVA Lines, and I needed a new valve from my regulator. This part plus a push fit fitting Does exactly that. (I used some yellow Teflon on the NPT out of habit) No leaks, perfect fit.

Was this review helpful to you?

View All Customer Reviews


Solder or Weld Thermo Probe Compression Fitting for pots/kegs PCOMP5 $13.00
Rubber Stopper, Solid, #7 $0.98