Home > Equipment > Keg, Pot, Cooler Parts > False Bottoms / Filters >

Elbow Connector for Domed False Bottoms
Elbow Connector for Domed False Bottoms
 
Alternative Views:
Our Price: $13.00

Quantity in Stock:2

Product Code: FBELBOW
Qty:

Description
 
You don't have to settle for the barbed elbow connector that comes with all the domed false bottoms out there. If you bought a domed false bottom from somewhere and found out that the inside diameter of the barb is a pathetic 1/4", this is your solution. Take a look at the comparison picture. You'll want to use a short piece of 1/2" ID silicone tubing to make the connection from this fitting over to your bulkhead fitting and that bulkhead needs at least a 1/2" barb.

This fitting fits into domed false bottoms with a 7/8" center hole.

Accessories
True Weldless Bulkhead - With Large BARB Silicone Tubing, Made in USA, 1/2" ID x 3/4" OD (1/8" Thick Walls) PER FOOT
Our Price: $15.00

Add
Our Price: $2.85

Add
True Weldless Bulkhead - With Large BARB Silicone Tubing, Made in USA, 1/2" ID x 3/4" OD (1/8" Thick Walls) PER FOOT

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 10 Click Here to Write a Review »

  0 of 0 people found the following review helpful:
 
5 of 5 March 17, 2021
Reviewer: Anthony Neal from Asheville, NC United States  
Always top notch! Excellent products, excellent service

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Check your depth January 15, 2019
Reviewer: Brian from OH  
Lay a straight edge across the bottom of false bottom and confirm you have an air gap between pickup and straight edge.
I purchased to replace the tiny little stainless barb that comes with typical false bottom conversion.  I replaced the original false bottom barb and filled mash tun with water to check that the bulkhead (also purchased the True bulkhead barb) for leaks.  All good!  I opened the valve to drain and only a trickle of water!  After some head scratching I determined that the pickup was basically flat against the bottom of cooler.  I removed the washer to create a 1/8 inch gap and flow was restored!

Was this review helpful to you?

  1 of 1 people found the following review helpful:
 
5 of 5 You Need This In Your Mash Tun July 18, 2016
Reviewer: Andrew Tucker from Waterford, MI United States  
I had a false bottom from another retailer in my 10 gallon beverage cooler mash tun for many years that had the 1/4" elbow fitting on it and that wasn't an issue for me when I was lautering via gravity, but, when I put that false bottom into a kettle to do direct-fired recirculating mashing, the restriction of that elbow (as well as the bulkhead/ball valve combo) was very apparent and became a problem. I swapped the elbow on the false bottom out for this one and put a true weldless bulkhead with large barb on the pot and have zero issues recirculating and lautering with a pump. I highly recommend this little piece of the flow puzzle. Cheers!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect fit February 7, 2016
Reviewer: Phil Beno from Brooklyn Hts, OH United States  
Went from a 1/4" ID to this 5/8" ID hose connection. Mash out went quicker without getting a stuck sparge. Another quality product.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 All Grain October 15, 2015
Reviewer: Carl Noble from Tell City, IN United States  
This is the way to go! Great flow.

Was this review helpful to you?

View All Customer Reviews


2 TC x 3/4" Female NPT Adapter $16.00
Hot Pod Kettle Element Enclosure 2ETC4S - TC2" Enclosure w/clamp, gasket, and 2" TC Radiused Solder Flange $67.00
CaraFoam, Weyermann LB $2.50
1.5" TC with 1/4" FFL on Top $13.00
Diptube or Racking Cane Filter Screen 600 Micron Mesh $14.99
Spike 20gal Plus False Bottom(TC pickup tube) $181.50
1/2" or 3/4" TC Silicone Gasket (Heat Resistant to 400F) $1.00
Flavoring, Natural, Watermelon, 4oz $4.39
1.5 TC x 1" Hose Barb $14.00